The goal is to develop applied innovation projects with companies to respond to the requirement to bring the teaching staff up to date in terms of science and technology, promoting innovation both in small and medium-sized companies and in vocational training centres.
For this, in addition to the knowledge and experience of our teaching staff, we make the facilities and equipment of the vocational training centers available to companies.
Within this environment, the following projects have been developed.
Collaboration in the construction of a collaborative bicycle workshop for the village
Tolosa Town Council, promoted by the Tolosaldea Garatzen Development Agency and the Zumardia Association, intended to install a bicycle workshop in a strategic point of the town's bidegorri, for which it was decided to join two modules located in the garbigune. We were asked to customise the work of this association process, the terrace and the slope, and the work equipment, as the work of the different trades had to be included, and the work had to be very specific and customised.
The geometries of the pieces had to be made to measure and special, which made the work difficult and hence our participation in the design and execution.
The theoretical and practical application of RITE
A project based on the preparation of technical consultancy and the interpretation and organization of the assembly strategy for the staff of a Gipuzkoa company. To this end, the identification of the differences between the new and the old regulations and their theoretical and practical application. In view of the scope of the work, the conditions which the Regulations on Thermal Installations in Buildings (RITE) must meet in order to meet the demand for thermal well-being and hygiene have been implemented in order to achieve adequate construction of heating, air conditioning and sanitary hot water facilities.
Papera prozesatzen duen makina baten prozesuaren animazio infografikoa
Gure bailaran kokatuta dagoen empresa honek, paper manipulazioko makina baten sorkuntzako prozesuen animazioabehar zuen, ondoren bere bezeroei erakusteko. Behin prozesua definituta, 3D animazioko programak erabiliz eta geometria prozesalaren bidez ziklagarria den animazio bat sortu da eta geometriak automatikoki sortzen duen sistema. Horretarako, gure ikastetxearekin batera, Bizkaiako Harrobia ikastolako 3D diseinuko taldeak hartu du parte.
Vacuum boxes for a manufacturing process
In order to work in the clean room of a company, special "vacuum" boxes are needed. For that purpose, they have been designed and manufactured in Tolosaldea using a specific geometry; and after choosing the appropriate material, they have been manufactured in specific dimensions.
Design and manufacture of suspension fork protection parts for mountain bikes in 3D printed polymer
Due to its use, the material must be hard, and it cannot be fragile. In addition, the measurement adjustment must be very precise. To do this, analysing the use, taking measurements, thinking of a design, building parts, testing them and making adjustments in size and design until the right design is reached.
Redesign and execution of destructive Test Tubes
One of the lines of work in this company is the preparation and machining of test tests for the railway and aeronautical industries, and when manufacturing them, in the case of certain tests, the requirements of the standard are difficult to meet from the point of view of adjustments and measures.
For this reason, the analysis of current machining strategies has been replaced by a rethink, with new parameterizations and applications.
3D scan of an artistic sculpture
This company needs to create the digital twin of a large sculpture that it has in its hands, and for this, with the knowledge and resources that we have in our center, the complete piece has been scanned and the CAM file to be created to be able to carry out 3D printing later.
It has been a complex job, due to the holes and complex shapes of the piece, but also attractive since it is a beautiful challenge to take steps in this learning process.
Collaboration in the construction of a 3D printing machine
This company, for an emerging 3D printing machine, once the design and structure had been determined, an aluminum structure had to be created, and taking advantage of the knowledge and resources of the welding teachers at our school, the structure had been built. Since it's not normal material, it's been a nice challenge.
Assembly, conditioning and commissioning of special cold rooms for the fertilisation of agricultural seeds
A centre that carries out agricultural studies needs special adapted cold rooms that are able to control the exact temperatures and humidity for the fertilisation of agricultural seeds, and that are able to control the exact temperatures and humidity, and to see the process.
For this purpose, a preparation process has been organised for 4 special cold rooms for the fertilisation and conservation of seeds, taking into account that each of them must be able to control the specific conditions of temperature and humidity.
It is then put into operation and given the manuals and explanations of parameterisation for the control of the process.
Suspension protection for an BTT
For mountain bikes known as Btt, the design and manufacture of suspension toothpaste protection parts in 3D printed polymer.
Because of the use given to it, the material must be hard, but equally it cannot be fragile, and the adjustment of the measures must be very precise.